Dryer
DPU 7360 GX
1 Important safety instructions
This section contains safety instructions
that will help protect from risk of personal
injury or property damage. Failure to
follow these instructions shall void any
warranty.
checked by a qualified electrician or
the Authorized Service Agent. Our
company shall not be liable for any
damages that will arise when the
product is used without grounding in
accordance with the local regulations.
The product should not be plugged
in during installation, maintenance,
cleaning and repair works.
Always have the installation and
repairing procedures carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
General safety
•
•
•
Never place the product on a carpet-
covered floor; otherwise, lack of
airflow beneath the machine will
cause electrical parts to overheat.
This will cause problems with your
product.
•
•
Do not operate the product if the
power cable / plug is damaged. Call
the Authorized Service Agent.
Do not make any changes on the
plug supplied with the product. If it is
not compatible with the socket, have
a qualified electrician change the
socket with a suitable one.
•
•
Do not use electrical devices in the
product.
Do not connect the air exit of the
product to the chimney holes which
are used for the exhaust fumes of the
devices operating with gas or other
types of fuel.
You must provide enough ventilation
in order to prevent gases exiting from
devices operating with other types of
fuels including the naked flame from
accumulating in the room due to the
back fire effect.
Items cleaned or washed with
gasoil/fuel oil, dry-laundry solvents
and other combustible or explosive
materials as well as the items that are
contaminated or spotted with such
materials should not be dried in the
product since they emit flammable or
explosive vapor.
•
•
Never touch the plug with wet hands!
Never unplug by pulling on the cable,
always pull out by grabbing the plug.
Connect the product to a grounded
outlet protected by a fuse of suitable
capacity as stated in the technical
specifications table.
•
•
•
Power cable of this product is
equipped with a conductor and
a grounding plug that allows for
grounding the product. This plug
must be inserted into a socket
which is installed and grounded in
accordance with the local laws and
regulations. Grounding installation
decreases the risk of electric shock
by opening a path with low resistance
for the electricity flow in case of a
malfunction or failure. Do not neglect
to have the grounding installation
made by a qualified electrician.
If you have any suspect about
the grounding installation, have it
•
•
Do not dry the laundry cleaned with
industrial chemicals in the dryer.
Oil-affected items can ignite
spontaneously, especially when
exposed to heat sources such as in
a tumble dryer. The items become
3 EN
warm, causing an oxidation reaction
in the oil. Oxidation creates heat. If
the heat cannot escape, the items
can become hot enough to catch fire.
Piling, stacking or storing oil-affected
items can prevent heat from escaping
and so create a fire hazard.
If it is unavoidable that fabrics that
contain vegetable or cooking oil or
have been contaminated by hair care
products be placed in a tumble dryer
they should first be washed in hot
water with extra detergent - this will
reduce, but not eliminate, the hazard.
Underwear that contains metal
reinforcements should not be dried in
the dryer. Dryer can get damaged if
metal reinforcements come loose and
break off during drying.
The final step of the drying
programme, namely the cool-down
step is performed without applying
heat to ensure that the laundry items
are kept at a temperature that will
not damage them. If you open the
loading door before the cool-down
step completes, hot vapour will come
out.
•
ANever stop the dryer before the
programme completes. If you must
do this, remove all laundry quickly
and lay them out to a suitable place
to dissipate the heat.
•
•
•
•
Always clean the lint filter before or
after each loading. Never operate the
dryer without the lint filter installed.
Clean inside and exhaust duct of the
product regularly. Do not allow fibre,
dust and dirt accumulation around
the exhaust exit and at adjacent
areas.
Power cable plug must be within easy
reach after installation.
Do not dry unwashed items in the
dryer.
Items soiled with cooking oils,
acetone, alcohol, fuel oil, kerosene,
stain removers, turpentine, paraffin
and paraffin removers must be
washed in hot water with plenty of
detergent before being dried in the
dryer.
Garments or pillows bolstered with
rubber foam (latex foam), shower
bonnets, water resistant textiles,
materials with rubber reinforcement
and rubber foam pads should not be
dried in the dryer.
Do not use fabric softeners and
anti-static products unless they are
recommended by the manufacturers
of the relevant product.
Use softeners, anti-static products
and etc. in accordance with the
Never attempt to repair the product
yourself. Do not perform any
repair or replacement procedures
on the product even if you know
or have the ability to perform the
required procedure unless it is
clearly suggested in the operating
instructions or the published service
manual. Otherwise, you will be
putting your life and others' lives in
danger.
For failures that you cannot remedy
by applying the procedures in safety
instructions, turn off and unplug
the product and call the Authorized
Service Agent.
•
•
•
•
•
•
•
Do not reach into the machine when
the drum is spinning.
Do not use extension cords, multi-
plugs or adaptors to connect the
dryer to power supply in order to
decrease the risk of fire and electric
shock.
Never wash the product by spreading
or pouring water onto it! There is the
risk of electric shock!
•
•
•
4 EN
instructions of their manufacturers.
Do not install the product behind a
door with a lock, sliding door or a
hinged door which can strike the
product.
Do not install or leave the dryer in
places where it will be exposed to
outdoor conditions.
Your product can be operated at
temperatures between +5°C and
+35°C. If the operating conditions fall
outside of this range, operation of the
product will be adversely affected and
it can get damaged.
Do not tamper with the controls.
Unplug the product when it is not in
use.
•
Product must only be used for
drying of textiles that are marked
accordingly.
•
•
•
•
Dry only those articles in your product
that are stated in this manual.
Remove all objects from pockets
such as lighters and matches.
This product is not intended to be
used by persons with physical,
sensory or mental disorders or
unlearned or inexperienced people
(including children) unless they are
attended by a person who will be
responsible for their safety or who will
instruct them accordingly for use of
the product.
•
•
•
•
Children's safety
•
•
Remove the loading door of
Electrical products are dangerous for
the children. Keep children away from
the product when it is operating. Do
not let them tamper with the product.
Do not allow children sit/climb on or
enter in the product.
Do not forget to close the loading
door when leaving the room where
the product is located.
Packaging materials are dangerous
to children. Keep the packaging
materials out of reach of children or
dispose them by classifying according
to waste directives.
the drying compartment before
decommissioning or disposing of the
product.
Check all garments before loading
and make sure that there is no any
lighters, coins, metal pieces, needles,
and etc. in their pockets or on them.
Make sure that the pets do not enter
into the product. Check the drum of
the product before using it.
•
•
•
•
•
•
Make sure that original spare parts
and accessories are used during
maintenance works.
•
•
Do not lean on the loading door when
it is open. The product may tip over.
When your machine is not in use
or when you unload the laundry
after completion of drying process,
turn the machine off with the On/
Off button. In cases where the On/
Off button is in On position (while
the machine is energized), keep the
loading door closed.
Intended use
•
This product has been designed for
domestic use. It should not be used
for other purposes.
5 EN
2 Installation
should stay at the same place where
its connections have been made.
When installing the product, make
sure that the rear wall of it does
not touch anywhere (tap, socket,
etc.). Also pay attention to select an
installation location which you will not
be required to change afterwards.
Place the product at least 1.5
cm away from the edges of other
furniture.
Refer to the nearest Authorized Service
Agent for installation of the product.
To make the product ready for use,
make sure that the electricity and water
drainage system are appropriate before
calling the Authorized Service Agent. If
they are not, call a qualified technician
and plumber to have any necessary
arrangements carried out.
•
CPreparation of the product's
location as well as the electrical and
BDo not place the product on the
waste water installations is under
customer's responsibility.
power cable.
BInstallation and electrical connections
Removing the transportation
safety assembly
of the product must be carried out
by the Authorized Service Agent.
Manufacturer shall not be held
liable for damages that may arise
from procedures carried out by
unauthorized persons.
ARemove the transportation safety
assembly before using the product for
the first time.
1. Open the loading door.
2. There is a nylon bag inside the drum
that contains a piece of styrofoam.
Hold it from its section marked with
XX XX.
3. Pull the nylon towards yourself and
remove the transportation safety
assembly.
APrior to installation, visually check if
the product has any defects on it. If
so, do not have it installed. Damaged
products cause risks for your safety.
ALet your dryer wait for 12 hours
before starting to use it.
Appropriate installation
location
•
•
•
•
Install the product on a stable and
level surface.
Dryer is heavy. Do not move it by
yourself.
Operate your product in a well
ventilated, dust-free environment.
Do not block the air ducts in front of
and under the product with materials
such as long pile rugs, wooden
blocks and bands.
AMake sure that no part of the
transportation safety assembly
remains inside the drum.
•
•
Do not install the product behind a
door with a lock, sliding door or a
hinged door which can strike the
product.
Under counter installation
•
This product can be installed under a
counter if the height of the counter is
sufficient.
Once the product is installed, it
6 EN
Connecting to the drain
In products equipped with condenser
unit, water accumulates in the water tank
during the drying cycle. You should drain
accumulated water after each drying
cycle.
You can directly drain accumulated water
through the water drain hose supplied
with the product instead of periodically
draining the water collected in the water
tank.
AWhile using undercounter dryer, it
should never be operated without
undercounter installation part.
Dryer Depth
60 cm
54 cm
Stock
number of
under-bench 2979600100 2973600100
installation
part
•
Leave at least 3 cm of space around
the sides and the rear wall of the
product when installing it under a
counter or in a cupboard.
Mounting over a washing
machine
•
A fixing device should be used
between the two machines
when installing the dryer above a
washing machine. The fixing device
(2977200100 white/2977200400
grey) must be installed by the
Authorized Service Agent.
Total weight of the washing machine
and the dryer -with full load- when
they are placed on top of each other
reaches to approx. 180 kilograms.
Place the products on a solid floor
that has sufficient load carrying
capacity!
Connecting the water drain hose
1. Pull hose in the product by hand in
order to disconnect it from where it is
connected. Do not use any tools to
remove the hose.
2. Connect one end of the drain hose
supplied separately with the product
to the connection point from where
you removed the hose of the product
in previous step.
•
3. Connect the other end of the drain
hose directly to the wastewater drain
or to the washbasin.
AHose must be fixed in every type
of connection. Your house will be
flooded if the hose comes loose
during water discharge.
CWater drain hose should be attached
7 EN
to a height of maximum 80 cm.
have a contact distance of minimum
3 mm.
CMake sure that the water drain hose
is not stepped on and it is not folded
BDamaged power cable must be
between the drain and the machine.
replaced by the Authorized Service
Agent.
Adjusting the feet
BIf the product is faulty, it must not be
In order to ensure that the product
operates more silently and vibration-free,
it must stand level and balanced on its
feet. Balance the machine by adjusting
the feet.
operated unless it is repaired! There is
the risk of electric shock!
First use
Before starting to use the product, make
sure that all preparations are made in
accordance with the instructions in
sections "Important safety instructions"
and "Installation".
Turn the feet to left or right until the
machine stands level and firmly.
Disposing of packaging
material
Packaging materials are dangerous to
children. Keep packaging materials in
a safe place away from reach of the
children.
Packaging materials of the product are
manufactured from recyclable materials.
Dispose of them properly and sort
in accordance with recycled waste
instructions. Do not dispose of them with
normal domestic waste.
Transportation of the product
1. Unplug the product before
transporting it.
2. Remove the water drain (if any) and
chimney connections.
CNever remove the adjustable feet
from their housings.
Electrical connection
Connect the product to a grounded outlet
protected by a fuse complying with the
values in the "Technical specifications"
table. Our company shall not be liable
for any damages that will arise when the
product is used without grounding in
accordance with the local regulations.
•
•
•
Connection must comply with
national regulations.
Power cable plug must be within easy
reach after installation.
The voltage and allowed fuse or
breaker protection are specified in
the “Technical specifications” section.
If the current value of the fuse or
breaker in the house is less than 10
Amps, have a qualified electrician
install a 10 Amp fuse.
3. Drain the water in the product
completely.
AWe recommend carrying the product
in upright position. If it is not possible
to carry the machine in the upright
position, we recommend carrying
it by tilting towards the right side
when looked from the front. After the
product is moved to its new place,
you should wait for 12 hours before
starting it.
•
•
•
The specified voltage must be equal
to your mains voltage.
Do not make connections via
extension cables or multi-plugs.
The main fuse and switches must
8 EN
Disposing of the old product
Dispose of the old product in an
environmentally friendly manner.
Refer to your local dealer or solid waste
collection centre in your area to learn how
to dispose of your product.
CWater collected during operation is
pumped to water tank. It is normal
to hear pumping noise during this
process.
For children's safety, cut the power
cable and break the locking mechanism
of the loading door so that it will be
nonfunctional before disposing of the
product.
Warnings about sounds
CIt is normal to hear metallic noise from
the compressor sometimes during
operation.
Technical specifications
EN
2
Height (adjustable)
Width
84,6 cm
59,5 cm
59,8 cm
7 kg
Depth
Capacity (max.)
Weight (net)
51,5 kg
Voltage
Rated power input
Model code
See type label
Type label is located behind the loading door.
9 EN
3 Preparations for drying
Things to be done for energy
machine is not in use.
Laundry suitable for drying in
the machine
saving
Following information will help you use
the product in an ecological and energy- CAlways obey the instructions given
on the garment tags. Dry only the
laundry having a label stating that
they are suitable for drying in a dryer
and make sure that you select the
appropriate programme.
efficient manner.
•
Operate the product at a capacity
suitable for the program you have
selected and pay attention not to
overload.
•
Spin your laundry at the highest
speed possible when washing them.
Thus, the drying time is shortened
and energy consumption is reduced.
Dry the same type of laundry
together.
Follow the instructions in the user
manual for programme selection.
Leave sufficient clearance at the
front and rear side of the dryer for
air circulation. Do not block the
ventilation grills at the front side of the
product.
A B C D
l n m
•
•
•
o p q
•
Do not open the loading door of
the machine during drying unless
necessary. If you must certainly open
the loading door, do not to keep it
open for a long time.
Laundry unsuitable for drying
in the machine
•
Laundry and items stated below are
not suitable for drying in a dryer:
Laundry items with metal
attachments such as metal buttons,
metal reinforcements or belt buckles.
Woolen or silk garments, nylon
stockings, delicate embroidered
fabrics and sleeping bags.
Garments made of delicate and
valuable fabrics.
•
•
Do not add new (wet) laundry during
drying.
•
Lint and fibres released from the
laundry to the air during the drying
cycle are collected in the Lint Filter.
Clean the lint filter before or after each
drying cycle.
Clean the filter drawer regularly either
when the Filter Drawer Cleaning
warning symbol appears or after
every 5 drying cycles
Ventilate the room, where the dryer is
located, well during drying.
For models with lamp, keep the door
closed if the On/Off button is pressed
(if the machine is energized) when
•
•
•
•
•
Tulle curtains.
Items made of hermetic fibres such
as pillows and quilts.
•
•
•
•
•
Very wet laundry items.
Unwashed dirty laundry items.
Laundry items containing rubber
foam or rubber.
10 EN
load more than the capacity values stated
in the table.
Items cleaned, washed or spotted
with gasoil/fuel oil, dry-laundry
solvents, industrial chemicals or other
combustible or explosive materials
should not be dried in the dryer.
Items soiled with cooking oils,
acetone, alcohol, fuel oil, kerosene,
stain removers, turpentine, paraffin
and paraffin removers must be
washed in hot water with plenty of
detergent before being dried in the
dryer.
CIt is not recommended to load the
dryer with laundry exceeding the
level indicated in the figure. Drying
performance will degrade when the
machine is overloaded. Furthermore,
dryer and the laundry can get
damaged.
Following weights are given as examples.
Approximate
weights (g)
Home articles
Preparing laundry for drying
Cotton quit covers
(double)
Cotton quit covers
(single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
1500
•
Check all garments before loading
and make sure that there is no any
lighters, coins, metal pieces, needles,
and etc. in their pockets or on them.
Laundry may be tangled after
washing. Separate the laundry items
before placing them into the dryer.
Sort the laundry according to their
types and thicknesses. Dry the same
type of laundry together. For instance,
thin kitchen towel and table cloths get
dry earlier than the thick bath towels.
1000
500
350
700
250
100
•
•
Bath towels
Hand towels
700
350
Approximate
weights (g)
150
Garments
CLaundry must be spun at the highest
Blouses
spin speed that the washing machine
allows on basis of the fabric type.
Correct load capacity
Cotton shirts
Shirts
Cotton dresses
Dresses
300
200
500
350
Jeans
700
Handkerchiefs (10
pieces)
T-Shirts
100
125
Follow the instructions in the “Programme
selection and consumption table”. Do not
11 EN
Loading the laundry
1. Open the loading door.
2. Place the laundry in the machine
without compressing.
3. Push the loading door to close.
AEnsure that no items are caught in
the door.
12 EN
4 Selecting a Programme and Operating Your Machine
Control panel
1
2
3
4
5
Shirts
Jeans
Daily
Xpress
Iron Dry
Synthetics
Wool
Refresh
Cupboard
Dry
Spin / Time
Time Delay
Mix
Iron Dry
Cupboard
Dry
Start/Pause
Sport
Cottons
Babycare
Delicates
Extra Dry
On / Off
Freshen Up
Cancel Press
& Hold 3 sec.
Timer
Programmes
Buzzer
Cancel
Dryness
Level
Anti-
Creasing
9
8
7
6
1. Washing Machine Spin Speed / Timer
Programme Selection button
2. Display
3. Start / Pause / Cancel button
4. Programme Selection knob
5. On / Off button
6. Anti-creasing button
7. Dryness Level button
8. Cancel Audio Warning button
9. Time Delay buttons
Spin speed / Timer programs*
Operation symbol
Pause symbol
Water Tank warning symbol
Filter cleaning warning symbol
Filter Drawer Cleaning warning symbol
Remaining Time indicator**
Child-proof Lock warning symbol
Time Delay mode
Loading door open warning symbol
Anti-creasing mode
Audio Warning Level / Cancel Audio Warning
Dryness Level
Anti-creasing is activated
*
Spin speed is used to show the remaining time more accurately. It does not
affect the performance of your machine.
** Time that appears on display indicates the remaining time until the end of the
programme and changes according to the dampness level of the laundry.
13 EN
Cupboard
Dry
Ventilation
Anti
Iron Dry
Cottons Synthetics
Extra dry
Express
Shirt
Timer
Creasing
programs
Child-proof
lock
Buzzer/ On/Off
cancel
Start
pause
cancel
Tank
full
Filter
Daily
Jeans
cleaning
Timer
Delay
Wool
Refresh
Dryness
Level
Babycare Sport
Spin
Mixed
Drying
Rack
Delicates
Preparing the machine
CFor further programme details,
1. Plug in the machine.
see "Programme selection and
2. Place the laundry in the machine.
3. Press the On / Off button.
consumption table".
Main programmes
Depending on the fabric type, the
following main programmes are available:
• Cottons
Dry durable laundry with this programme.
Dries at normal temperature. It is
recommended to use for your cotton
items (bed sheets, quilt covers, towels,
bathrobes, etc.).
CPressing the On / Off button does
not necessarily mean that the
programme has started. Press Start
/ Pause / Cancel button to start the
programme.
Programme selection
1. Decide the appropriate programme
from the table below which includes
drying levels.
2. Select the desired programme with
the Programme Selection knob.
Only the cotton laundry
• Synthetics
Dry less durable laundry with this
programme. Recommended for
synthetics.
Additional programmes
For special cases, following additional
programmes are available in the machine.
is dried at normal
temperature. Thick and
multi layered laundry
Extra Dry
(towels, linens, jeans and
etc.) are dried in a way that
they do not require ironing
before being placed in the
wardrobe.
CAdditional programs may differ
according to the features of your
machine.
• Express
You can use this program to dry your
cotton laundry that you have spun at
high speeds in your washing machine.
This program dries 1 kg cotton laundry (3
Shirts/3T-shirts) in 45 minutes.
Normal laundry
(tablecloths, underwear
Cupboard and etc.) are dried in a way
dry
that they do not require
ironing before being placed
in the wardrobe.
CTo obtain better results from your
dryer, your laundry must be washed
Normal laundry (shirts,
dresses and etc.) are dried
ready to be ironed.
at suitable programs and spun at the
recommended speed in the washing
Iron Dry
14 EN
machine.
• Shirt
This programme dries the shirts more
sensitively and creases them less and
thus, helps to iron them more easily.
Take your laundry immediately out
of the dryer and hang them after the
program is over in order to prevent
them from getting creased.
• Freshen up
Only ventilation is performed for 10
minutes without blowing hot air. You can
air the clothes that have been kept at
closed environments for a long time and
deodourise unpleasant odours thanks to
this programme.
CThere may be a little moisture on the
shirts at the end of the programme.
We recommend you not to leave the
shirts in the dryer.
• Jeans
Use this programme to dry your jeans
that are spun at high speeds in the
washing machine.
• Timer programmes
You can select one of the 10 min., 20
min., 30 min., 40 min., 50 min., 60 min.,
80 min., 100 min., 120 min., 140 min.
and 160 min. timer programmes to
achieve the desired final drying level at
low temperatures.
• Mixed
Use this programme to dry non-
pigmenting synthetic and cotton laundry
items together.
• Sport
Use this programme to dry together the
synthetic and cotton laundry items and
the laundry items made of mixed fabrics.
• Wool Refresh
CWith this programme, the machine
dries for the time selected regardless
of the dryness level.
You can use this program to ventilate
and soften your woolen laundry that can
be washed in the washing machine. Do
not use this program to dry your laundry
completely. Take out your laundry and
ventilate them immediately after the
program is over.
• Daily
This program is used to dry cottons and
synthetics daily, and lasts for 1.5 hour.
• Babycare
This program is used for baby clothes
that bear machine dryable approval on its
label.
• Delicates
You can dry your highly delicate laundry
that are suitable for drying or laundry
which is advised to be hand-washed at a
lower temperature.
CIt is recommended to use a cloth bag
to prevent certain delicate laundry
from getting creased or damaged.
15 EN
Programme selection and consumption table
EN
Approximate
amount of
remaining
humidity
Spin speed in
Drying time
(minutes)
Programs
Capacity (kg)
washing machine
(rpm)
Cottons / Coloreds
Extra dry
7
7
7
1000
1000
1000
% 60
% 60
% 60
175
156
125
A
Cupboard dry
A
Iron dry
A
Babycare
3
1.5
4
1000
1200
1200
1200
1000
1000
1200
600
% 60
%50
%50
%50
%60
%60
%50
%40
%50
80
50
Shirt
Jeans
120
90
Daily
4
Mixed
4
115
105
45
Sport
4
Express
Delicates
Wool Refresh
Synthetics
1
2
55
1.5
600
8
Cupboard dry
3.5
3.5
800
800
% 40
% 40
62
50
B
Iron dry
B
Energy consumption values
Energy consumption value kWh per
year
Programs
Capacity (kg)
Energy rating star
6
Cottons-Extra Dry*
7
163
* : Energy Label standard program (AS/NZS 2442)
All values given in the table have been fixed according to standard laboratory
conditions. These values may deviate from the table according to the laundry type,
laundry spin speed, environmental conditions and voltage fluctuations.
16 EN
Auxiliary functions
Audio Warning
The machine will give an audio warning
when the programme comes to an end.
If you do not want the machine give an
audio warning, press the Volume Level
button repeatedly until "x" appears on the
display. Use the same button to adjust
the volume level.
CPress Anti-creasing button to activate
this function.
Changing the contrast
CYou can activate this function either
Adjust the display contrast in order to
make the symbols on the display appear
clearer. It may particularly be necessary to
change the contrast setting of the display
when the dryer is installed over a washing
machine.
before or after the programme starts.
Cancel
audio warning
Audio warning Audio warning
level 1 level 2
Audio warning
level 3
Dryness level
Press and hold the Spin Speed / Timer
Programme button for 3 seconds.
When the contrast is changed, all
symbols on the display will appear for
3 seconds in order to indicate that the
process is complete.
Used to adjust the required dryness level.
More drying is performed compared
to the default settings when "+" sign
appears and less drying is performed
when "-" sign appears. Programme
duration can change depending on the
selection.
CPerform the same procedure to revert
back to the previous contrast setting.
CYou can activate this function only
Warning symbols
before the programme has started.
CWarning symbols may differ
according to the model of your
machine.
Lint filter cleaning
Anti-creasing
When the programme is completed, a
warning symbol will appear to remind that
the filter needs to be cleaned.
You can use Anti-creasing function to
prevent laundry from creasing if you will
not take the laundry out after the program
has come to an end. This program
rotates the laundry in every 240 second
for 2 hours to prevent creasing.
If the Filter Cleaning symbol flashes
C
continuously, refer to “Troubleshooting”
section.
Anti-creasing is activated but the
programme is still running in the first
display image below. Drying cycle is
completed and the Anti-creasing step has
started in the second display image.
Water tank
When the programme is completed, a
warning symbol will appear to remind that
the water tank needs to be drained.
If the water tank becomes full while
the programme is running, the warning
symbol will start to flash and machine will
17 EN
pause. Drain the water in the water tank
and press Start / Pause / Cancel button
to resume the programme. The warning
symbol turns off and the programme
resumes operating.
countdown process, Time Delay
symbol disappears, drying process
starts and the programme duration
is displayed. The time on the display
is the total of normal drying time and
delay time.
Cleaning of filter drawer
Warning symbol flashes with certain
intervals to remind that the filter drawer
needs to be cleaned.
Time Delay is activated by pressing the
Start / Pause / Cancel button in the
above display image.
Changing the delay time
If you want to change the time during
countdown:
Loading door open
This warning symbol appears when the
loading door of the dryer is open.
1. Press Start / Pause / Cancel
button for 3 seconds to cancel the
programme. Repeat the Time Delay
procedure for the desired time.
2. Set the desired delay time with Time
Delay + and - buttons. The Time
Delay symbol will flash.
3. Press Start / Pause / Cancel button.
The Time Delay starts to count down.
The Time Delay symbol lights up.
Pause symbol disappears. Start
symbol appears.
4. The “:” in the middle of the displayed
delay time will start flashing.
Cancelling the Time Delay
If you want to cancel the Time Delay
countdown and start the programme
immediately:
1. Press Start / Pause / Cancel
button for 3 seconds to cancel the
programme.
Time Delay
Time Delay function allows you to delay
the startup of the programme up to 24
hours.
1. Open the loading door and put the
laundry in.
2. Select the drying programme, spin
speed and, if required, the auxiliary
functions.
3. Press Time Delay buttons + and - to
set the desired time delay. The Time
Delay symbol will flash.
4. Press Start / Pause / Cancel button.
The Time Delay starts to count down.
The Time Delay symbol lights up.
Start symbol appears. The “:” in the
middle of the displayed delay time will
start flashing.
2. Press Start / Pause / Cancel button
to start the programme you have
previously selected.
CAdditional laundry may be loaded
/ taken out during the Time Delay
period. At the end of the Time Delay
18 EN
Starting the programme
Press Start / Pause / Cancel button to
start the programme.
Start / Pause symbol will light up to
indicate that the programme has started
and ":" symbol between the remaining
time will continue flashing.
Child-proof Lock
Machine is equipped with a Childproof
Lock which prevents interfering with the
current programme flow by pressing
any button. All buttons except the On
/ Off button on the control panel are
deactivated when the Child-proof Lock is
active.
In order to activate the Childproof Lock,
press Audio Warning and Anti-Creasing
buttons simultaneously for 3 seconds.
To start a new programme after the
current programme is over or to interrupt
the current programme, the Child-proof
Lock should be deactivated. Press the
same buttons for 3 seconds again to
deactivate the Child-proof Lock.
Progress of programme
Anti-
creasing
Drying
Wardrobe
(Extra)
Iron
Ventilation
Progress of a running programme is
indicated on the display by means of a
set of symbols.
At the beginning of each programme
step, the relevant symbol in the series of
symbols will light up and thus, at the end
of the programme, all symbols will remain
lit up. The rightmost symbol on the
display indicates the step being carried
out.
CLock symbol will appear on the
display when the Child-proof Lock is
activated.
CChild-proof Lock is deactivated when
the machine is switched off and on
Drying
with On / Off button.
Drying symbol lights up in all programmes
apart from ventilation.
Iron Dry
Starts to illuminate when the dryness level
reach Iron Dry step.
Cupboard dry
Starts to illuminate when the dryness level
reach Wardrobe Dry step.
Extra dry
Starts to illuminate when the dryness level
reach Wardrobe Dry Extra step.
Ventilation
When the Child-proof Lock is activated:
•
Display symbols will not change
even if the position of Programme
Selection knob is changed while the
machine is running or in halt.
•
If the Child-proof Lock is deactivated
after changing the position of
the Programme Selection knob
while the machine is running, the
machine stops and new programme
information is displayed.
Changing the programme after
Ventilation symbol illuminates when the
programme comes to an end.
it has started
After the machine starts, you can change
the selected programme and dry your
laundry in a different programme.
CAnti-creasing symbol will illuminate
at the end of the programme if Anti-
creasing function is activated.
19 EN
1. If you want to select Extra Dry
programme instead of Iron Dry
programme, press and hold the
Start / Pause / Cancel button for 3
seconds to cancel the programme.
2. Select Extra Dry programme by
turning the Programme Selection
knob.
However, this process will increase
the programme time and energy
consumption since the drying
process will be interrupted repeatedly.
Therefore, it is recommended to add
laundry before the drying programme
has started.
CIf you select a new programme by
3. Press Start / Pause / Cancel button
to start the programme.
turning the Programme Selection
knob while your machine is in Pause
mode, then the current program
is aborted and new programme
information is displayed.
Do not touch the inner surface of
the drum when adding or taking
out laundry while a programme is
running. Surfaces of the drum are
hot.
CYou can also select a new
programme by turning the
Programme Selection knob while the
machine is operating. In this case,
current programme is aborted and
the new programme information
appears on the display.
Canceling the programme
If you want to stop drying and cancel
the programme for any reason after the
machine has started to run, press and
hold the Start / Pause / Cancel button
for 3 seconds. Lint Filter Cleaning and
Water Tank warning symbols light up and
"End" label appears on the display as a
reminder at the end of this period.
Adding / removing laundry in Pause
mode
In order to add or take out laundry after
the drying programme has started:
1. Press Start / Pause / Cancel button
to switch the machine to Pause
mode. Drying process will stop.
2. While in Pause mode, open the
loading door, add or take out laundry
and close the loading door.
3. Press Start / Pause / Cancel button
to start the programme.
AAs the inside of the machine will be
excessively hot when you cancel
CAny laundry added after the drying
the programme while the machine
is running, activate the ventilation
program to cool it down.
process has started may cause the
clothes that are already dried in the
machine intermingle with wet clothes
and the result will be wet laundry after
the drying process is over.
CMachine will stop if you turn the
Programme Selection knob while
it is operating. In this case, current
programme is aborted and the new
programme information appears on
CYou may repeat laundry adding
or removing process as many
times as you desire during drying.
20 EN
the display.
End of programme
Lint Filter Cleaning and Water Tank
warning symbols light up in the
programme follow-up indicator and
"End” label appears on the display when
the programme comes to an end. The
loading door can be opened and the
machine becomes ready for a second
cycle.
Press On / Off button to switch off the
machine.
CIf Anti-creasing function is activated
and the laundry is not taken from
the machine at the end of the
programme, 2-hours Anti-creasing
programme is activated.
CClean the lint filter after each drying.
(See “Lint Filter / Loading Door Inner
Surface”)
CDrain the water tank after each drying
cycle. (See "Draining the water tank")
21 EN
5 Maintenance and cleaning
Service life of the product extends and
frequently faced problems decrease if
cleaned at regular intervals.
up on the lint filter surface. Dry the lint
filter completely before reinstalling it.
BThis product must be unplugged
during maintenance and cleaning
works (control panel, body, etc.).
Lint Filter / Loading Door Inner
Surface
Lint and fibres released from the laundry
to the air during the drying cycle are
collected in the Lint Filter.
CClean the entire inner surface of
the loading door and loading door
gasket.
C*Such fibre and lint are generally
formed during wearing and washing.
AAlways clean the lint filter and the
inner surfaces of the loading door
after each drying process.
CYou can clean the lint filter housing
with a vacuum cleaner.
To clean the lint filter:
1. Open the loading door.
Cleaning the sensors
2. Remove the lint filter by pulling it up
and open the lint filter.
3. Clean lint, fibre, and cotton raveling
by hand or with a soft piece of cloth.
4. Close the lint filter and place it back
into its housing.
CA layer can build up on the lint filter
pores that can cause clogging of the
lint filter after using the machine for a
while. Wash the lint filter with warm
water to remove the layer that builds
22 EN
There are dampness sensors in the
machine that detect whether the laundry
is dry or not.
2. Drain the water in the tank.
To clean the sensors:
1. Open the loading door of the
machine.
2. Allow the machine to cool down if it is
still hot due to the drying process.
3. Wipe the metal surfaces of the sensor
with a soft cloth, dampened with
vinegar and dry them.
3. If there is lint accumulation in the
funnel of the water tank, clean it
under running water.
CClean metal surfaces of the sensors 4
times a year.
CDo not use metal tools when cleaning
4. Place the water tank into its seat.
Cleaning the filter drawer
Lint and fibre that could not be captured
by the lint filter are blocked in the filter
drawer behind the kick plate. Filter
Drawer Cleaning warning light will light up
maximum at every 5 drying cycles as a
metal surfaces of the sensors.
ANever use solvents, cleaning agents
or similar substances for cleaning due
to the risk of fire and explosion!
Draining the water tank
Dampness of the laundry is removed and
condensed during drying process and the reminder.
water that arise accumulates in the water
tank. Drain the water tank after each
drying cycle.
There is a two-level filter in the filter
drawer. The first level is the filter drawer
sponge and the second level is the filter
cloth.
To clean the filter drawer:
1. Press the kick plate button to open
the kick plate.
ACondensed water is not potable!
ANever remove the water tank when
the programme is running!
If you forget to drain the water tank, the
machine will stop during the subsequent
drying cycles when the water tank is full
and the Water Tank warning symbol will
flash. If this is the case, drain the water
tank and press Start / Pause / Cancel
button to resume the drying cycle.
To drain the water tank:
1. Pull the drawer and remove the water
tank carefully.
23 EN
2. Remove the filter drawer cover by
6. Clean lint, fibre, and cotton raveling
on the filter cloth by hand or with a
soft piece of cloth.
turning it in the direction of arrow.
3. Pull out the filter drawer.
CWhen you notice a layer that may
lead clogging on filter cloth, please
clean the layer by washing in
warm water. Let the filter cloth dry
thoroughly before installing back the
filter drawer.
7. Hand-wash the filter drawer’s sponge
to remove hair and lint on it. Squeeze
the sponge by hand to remove
excessive water.
4. Open the filter drawer by pressing the
CIt is not necessary to clean the
red button.
sponge if lint and fibre accumulation
on it is not significant.
8. Place the sponge back into its place.
5. Take out the filter drawer sponge.
9. Close the filter drawer as to lock the
red button.
24 EN
10. Place the filter drawer back into its
place, turn the filter drawer cower
clockwise making sure that it is
closed securely.
Cleaning the evaporator
Clean the lints accumulated on the fins
of the evaporator located behind the filter
drawer with a vacuum cleaner.
11. Close the kick plate cover.
CYou can also clean by hand provided
that you wear protective gloves. Do
not attempt to clean with bare hands.
CDrying without the filter drawer
sponge in place will damage the
machine!
CA dirty lint filter and filter drawer will
cause longer drying periods and
higher energy consumption.
CA layer can build up on the lint filter
pores that can cause clogging of the
lint filter after using your machine for
a while. Wash the lint filter with warm
water to remove the layer that builds
up on the lint filter surface. Dry the lint
filter completely before using it.
25 EN
6 Troubleshooting
Drying process takes too much time.
•
•
•
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.
Ventilation grids on the front side of the machine are blocked. >>> Remove the
objects (if any) that block ventilation in front of the ventilation grids.
Ventilation is not sufficient since the room where the machine is installed is
very small. >>> Open the door and window of the room to avoid the room
temperature increase too much.
•
•
Lime deposit has built up on the dampness sensor. >>> Clean the dampness
sensor.
•
•
Excessive laundry is loaded. >>> Do not load the dryer in excess.
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your
washing machine.
Laundry comes out wet at the end of drying.
CAfter drying, the hot clothes feel damper than their actual dampness level.
•
It is likely that the selected programme did not suit the laundry type.>>>Checking
the care labels on clothes, select appropriate programme for the laundry type or
use timer programmes in addition.
•
•
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter
drawer.
•
•
Excessive laundry is loaded. >>> Do not load the dryer in excess.
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your
washing machine.
Dryer does not switch on or the programme does not start. Dryer does not start
when it is set.
•
•
•
It is not plugged in. >>> Make sure that the machine is plugged in.
The loading door is ajar. >>> Make sure that the loading door is closed securely.
Programme is not selected or the Start / Pause / Cancel button is not pressed.
>>> Make sure that the programme is selected and the machine is not in Pause
mode.
•
Childproof Lock is activated. >>> Deactivate the Childproof Lock.
Programme is interrupted without any cause.
•
•
Loading door is ajar. >>> Make sure that the loading door is closed securely.
There was a power failure. >>> Press Start / Pause / Cancel button to start the
programme.
•
Water tank is full. >>> Drain the water tank.
Laundry has shrunk, become felted or deteriorated.
•
A programme suitable for the laundry type is not used. >>> Check the garment
tag and select a programme suitable for the fabric type.
26 EN
Drum lighting does not turn on. (On models with lamp)
•
Dryer is not switched on with the On / Off button. >>> Make sure that the dryer is
switched on.
•
Lamp is defective. >>> Call Authorized Service Agent to have the lamp replaced.
End/Anti-creasing symbol is on.
•
Anti-creasing programme is activated in order to prevent laundry that has
remained in the machine from creasing. >>> Turn off the dryer and take out the
laundry.
End symbol is on.
Programme is over. Turn off the dryer and take out the laundry.
Lint Filter Cleaning symbol is on.
Lint filter is not cleaned. >>> Clean the lint filter.
Lint Filter Cleaning symbol is flashing.
•
•
•
•
Filter housing is clogged with lints. >>> Clean the lint filter housing.
A deposit has built up on the lint filter pores that may cause clogging. >>> Wash
the lint filter with warm water.
•
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter
drawer.
Water leaks from the loading door
•
Lint has accumulated on the inner surfaces of the loading door and on the
surfaces of the loading door gasket. >>> Clean the inner surfaces of the loading
door and the surfaces of the loading door gasket.
Loading door opens spontaneously.
•
Loading door is ajar. >>> Push the loading door to close until you hear a locking
sound.
Water Tank warning symbol is on/flashing.
•
•
Water tank is full. >>> Drain the water tank.
Water draining hose is bent. >>> If the product is connected directly to a
wastewater drain, check the water drain hose.
Filter Drawer Cleaning warning symbol is flashing.
•
Filter drawer is not cleaned. >>> Clean the sponge and the filter cloth in the filter
drawer.
AIf you cannot eliminate the problem although you follow the instructions in this
section, consult your dealer or the Authorized Service Agent. Never try to repair a
nonfunctional product yourself.
27 EN
|