Dryer
DPY 8506 GXB1
User Manual
2960311036_EN/220115.1715
1 Important instructions for safety and
environment
This section contains safety instructions that will help protect from risk of
personal injury or property damage. Failure to follow these instructions shall
void any warranty.
1.1 General safety
•The dryer can be used by children at and above 8 years old and by
persons whose physical, sensory or mental capabilities were not fully
developed or who lack experience and knowledge provided that they
are supervised or trained on the safe usage of the product and the risks
it brings out. Children should not play with the product. Cleaning and
maintenance works should not be performed by children unless they are
supervised by someone.
•Children of less than 3 years should be kept away unless continously
supervised.
•Adjustable feet should not be removed. The gap between the dryer and
the floor should not be reduced with materials such as carpet, wood and
tape. This will cause problems with the dryer.
•Always have the installation and repairing procedures carried out by the
Authorized Service. Manufacturer shall not be held liable for damages
that may arise from procedures carried out by unauthorized persons.
•Never wash the dryer by spraying or pouring water onto it! There is the
risk of electric shock!
Dryer / User Manual
3 / 32 EN
Important instructions for safety and environment
1.1.1 Electrical safety
A Electrical safety instructions should be followed while electrical
connection is made during the installation.
•Connect the dryer to a grounded outlet protected by a fuse at the value
specified on the type label. Have the grounding installation performed by
a qualified electrician. Our company shall not be liable for any damages
that will arise when the dryer is used without grounding in accordance
with the local regulations.
•The voltage and allowed fuse protection is stated on the type label plate.
•The voltage specified on the type label must be equal to your mains
voltage.
•Unplug the dryer when it is not in use.
•Unplug the dryer from the mains during installation, maintenance,
cleaning and repair works.
•Do not touch the plug with wet hands! Never unplug by pulling on the
cable, always pull out by grabbing the plug.
•Do not use extension cords, multi-plugs or adaptors to connect the dryer
to power supply in order to decrease the risk of fire and electric shock.
•Power cable plug must be easily accessible after installation.
B Damaged mains cable should be changed notifying the Authorized
B If the dryer is faulty, it must not be operated unless it is repaired
Service.
by an authorized service agent! There is the risk of electric shock!
Dryer / User Manual
4 / 32 EN
Important instructions for safety and environment
1.1.2 Product safety
Points to be taken into consideration for fire hazard:
Below specified laundry or items must not be dried
in the dryer considering fire hazard.
•Unwashed laundry items
•Items soiled with oil, acetone, alcohol, fuel oil, kerosene, stain
removers, turpentine, paraffin or paraffin removers must be
washed in hot water with plenty of detergent before being dried
in the dryer.
For this reason especially the items containing the above
specified
stains must be washed very well, to do this
use adequate detergent and choose a high washing
temperature.
Below specified laundry or items must not be dried in the
dryer due to the fire hazard:
•Garments or pillows bolstered with rubber foam (latex foam),
shower bonnets, water resistant textiles, materials with rubber
reinforcement and rubber foam pads.
•Clothing cleaned with industrial chemicals.
Items such as lighter, match, coins, metal parts, needle etc.
may damage the drum set or may lead to functional problems.
Therefore check all the laundry that you will load into your dryer.
Never stop your dryer before
the programme completes. If you must do this, remove all
laundry
quickly and lay them out to dissipate the heat.
Clothes that are washed inadequately may ignite on their own
and even may ignite after drying ends.
Dryer / User Manual
5 / 32 EN
Important instructions for safety and environment
•You must provide enough ventilation in order to prevent gases exiting from
devices operating with other types of fuels including the naked flame from
accumulating in the room due to the back fire effect.
Underwear that contains metal reinforcements should not be
A
dried
in the dryer. Dryer may be damaged if metal reinforcements come
loose and break off during drying.
Use softeners and similar products in accordance with the
instructions of their manufacturers.
C
C
Always clean the lint filter before or after each loading. Never
operate the dryer without the lint filter installed.
•Never attempt to repair the dryer by yourself. Do not perform any repair
or replacement procedures on the product even if you know or have the
ability to perform the required procedure unless it is clearly suggested in
the operating instructions or the published service manual. Otherwise, you
will be putting your life and others’ lives in danger.
•There must not be a lockable, sliding or hinged door that may block
the opening of the loading door in the place where your dryer is to be
installed.
•Install your dryer at places suitable for home use. (Bathroom, closed
balcony, garage etc.)
•Make sure that pets do not enter the dryer. Check the inside of the dryer
before operating it.
•Do not lean on the loading door of your dryer when it is open, otherwise it
may fall over.
•The lint must not be allowed to accumulate around the tumble dryer
Dryer / User Manual
6 / 32 EN
Important instructions for safety and environment
1.2 Mounting over a washing machine
•A fixing device should be used between the two machines when installing
the dryer above a washing machine. The fitting device must be installed
by the authorized service agent.
•Total weight of the washing machine and the dryer -with full load- when
they are placed on top of each other reaches to approx. 180 kilograms.
Place the products on a solid floor that has sufficient load carrying
capacity!
Washing machine cannot be placed on the dryer. Pay attention
to the above warnings during the installation on your washing
A machine.
Installation Table for Washing Machine and Dryer
Washing Machine Depth
Dryer Depth
62cm 60 cm 54 cm 50 cm 49 cm 45 cm 40 cm
Can be
Can be
Can be
Can be
Can be
Can be Cannot be
54 cm
60 cm
installed installed installed installed installed installed installed
Can be
Can be
Can be
Can be
Can be Cannot be Cannot be
installed installed installed installed installed installed installed
Dryer / User Manual
7 / 32 EN
Important instructions for safety and environment
1.3 Intended use
•Dryer has been designed for domestic use. It is not suitable for
commercial use and it must not be used out of its intended use.
•Use the dryer only for drying laundry that are marked accordingly.
•The manufacturer waives any responsibility arisen from incorrect usage or
transportation.
•The service life of the dryer that you purchased is 10 years. During this
period, original spare parts will be available to operate the dryer properly.
1.4 Child safety
•Packaging materials are dangerous for the children. Keep packaging
materials away from children.
•Electrical products are dangerous for the children. Keep children away
from the product when it is operating. Do not let them tamper with the
dryer. Use the child-proof lock in order to prevent the children to tamper
with the dryer.
Child-proof lock is on the control panel. (See Child lock)
C
•Keep loading door closed even when the dryer is not in use.
Dryer / User Manual
8 / 32 EN
Important instructions for safety and environment
1.5 Compliance with the WEEE regulation
and disposing of the waste product
This product complies with EU WEEE Directive (2012/19/EU). This
product bears a classification symbol for waste electrical and
electronic equipment (WEEE).
This product has been manufactured with high quality parts and
materials which can be reused and are suitable for recycling. Do
not dispose of the waste product with normal domestic and other
wastes at the end of its service life. Take it to the collection center for the
recycling of electrical and electronic equipment. Please consult your local
authorities to learn about these collection centers.
1.6 Compliance with RoHS Directive:
The product you have purchased complies with EU RoHS Directive
(2011/65/EU). It does not contain harmful and prohibited materials
specified in the Directive.
1.7 Package information
Packaging materials of the product are manufactured from recyclable
materials in accordance with our National Environment Regulations. Do
not dispose of the packaging materials together with the domestic or other
wastes. Take them to the packaging material collection points designated
by the local authorities.
Please visit the following website to get more information on the product.
Dryer / User Manual
9 / 32 EN
Important instructions for safety and environment
1.8 Technical Specifications
EN
Height (min. / max.)
Width
Depth
84,6 cm / 86,6 cm*
59,5 cm
60,9 cm
8 kg**
Capacity (max.)
Net weight (plastic front door usage)
Net weight (glass front door usage)
Voltage
50,5 kg
52,5 kg
Rated power input
Model code
See type label***
* Min. height: Height with adjustable feet are closed.
Max. height: Height with adjustable feet are opened maximum.
** Dry laundry weight before washing.
*** Type label is located behind the loading door.
Technical specifications of the dryer are subject to specification
without notice to improve the quality of the product.
Figures in this manual are schematic and may not match the
product exactly.
Values stated on markers on the dryer or in the other published
documentation accompanying with the dryer are obtained in
laboratory in accordance with the relevant standards. Depending
on operational and environmental conditions of the dryer, these
values may vary.
C
C
C
Dryer / User Manual
10 / 32 EN
2 Your Dryer
2.1 Package Contents
1
2
3
4
5
1. Water drain hose *
2. Filter drawer spare sponge*
3. User Manual
4. Drying basket*
5. Drying basket user manual*
*It can be supplied with your machine depending on its model.
Dryer / User Manual
11 / 32 EN
3 Installation
Before the calling the nearest Authorized Service for the
installation of the dryer, ensure that electrical installation
and water drain is appropriate referring to the user's
manual.(See 3.3 Connecting to the drain and 3.5
Electrical connection) If they are not suitable, contact
a qualified electrician and technician to make necessary
arrangements.
Do not place the dryer on the power
cable.
B
3.2 Removing the transportation
safety assembly
Remove the transportation safety
assembly before using the dryer for the
first time.
A
Preparation of the dryer's location
as well as the electrical and waste
•
•
Open the loading door.
water installations is under customer's
C
There is a nylon bag inside the drum that contains
a piece of styrofoam. Hold it from its section
marked with XX XX.
Pull the nylon towards yourself and remove the
transportation safety assembly.
responsibility.
Prior to installation, visually check if the
dryer has any defects on it. If the drier
A is damaged, do not have it installed.
Damaged products cause risks for your
safety.
•
Let your dryer wait for 12 hours before
starting to use it.
A
3.1 Appropriate installation location
Install the dryer on a stable and level surface.
Dryer is heavy. Do not move it by yourself.
•
Operate your dryer in a well ventilated, dust-free
environment.
•
The gap between the dryer and the surface should
not be reduced by the materials such as carpet,
wood and tape.
Do not cover the ventilation grills of the dryer.
There must not be a lockable, sliding or hinged
door that may block the opening of the loading
door in the place where your dryer is to be
installed.
Once the dryer is installed, it should stay at the
same place where its connections have been
made. When installing the dryer, make sure that
its rear wall does not touch anywhere (tap, socket,
etc.).
Place the dryer at least 1 cm away from the edges
of other furniture.
Your dryer can be operated at temperatures
between +5°C and +35°C. If the operating
conditions fall outside of this range, operation of
the dryer will be adversely affected and it can get
damaged.
The rear surface of the tumble dryer shall be
placed against a wall.
Check that no part of the transportation
safety assembly remains inside the drum.
A
•
•
3.3 Connecting to the drain
In products equipped with condenser unit, water
accumulates in the water tank during the drying cycle.
You should drain accumulated water after each drying
cycle.
You can directly drain accumulated water through the
water drain hose supplied with the product instead of
periodically draining the water collected in the water
tank.
•
•
•
Connecting the water drain hose
1-2 Pull hose at the behind of the dryer by hand in
order to disconnect it from where it is connected.
Do not use any tools to remove the hose.
3
Connect one end of the drain hose supplied with
the dryer to the connection point from where you
removed the hose of the product in previous step.
•
4
Connect the other end of the drain hose directly to
the wastewater drain or to the washbasin.
Dryer / User Manual
12 / 32 EN
Installation
3.5 Electrical connection
For specific instructions for electrical connection
required during installation (see 1.1.1 Electrical
Safety)
1
2
4
3.6 Transportation of the dryer
Unplug the dryer before transporting it.
Drain all water that has remained in the dryer.
If direct water drain connection is made, then remove
the hose connections.
3
We recommend carrying the dryer in
upright position. If it is not possible to
carry the machine in the upright position,
we recommend carrying it by tilting
A
towards the right side when looked from
the front.
3.7 Warnings about sounds
Hose connection should be made in a
safe manner. Your drain house will be
flooded if the hose comes out of its
housing during water discharge.
It is normal to hear a metallic noise
from the compressor sometimes during
A
operation.
C
Water drain hose should be attached to a
height of maximum 80 cm.
C
C
Make sure that the water drain hose
is not stepped on and it is not folded
between the drain and the machine.
3.4 Adjusting the feet
•
In order to ensure that the dryer operates more
silently and vibration-free, it must stand level and
balanced on its feet. Balance the machine by
adjusting the feet.
•
Turn the feet to left or right until the dryer stands
level and firmly.
Water collected during operation is
pumped to water tank. It is normal to hear
pumping noise during this process.
C
Never unscrew the adjustable feet from
their housings.
C
Dryer / User Manual
13 / 32 EN
4 Preparation
4.1 Laundry suitable for drying in the dryer
Always obey the instructions given on the garment tags. Dry only the laundry having a label stating that they are
suitable for drying in a dryer and make sure that you select the appropriate programme.
LAUNDRY DRYING SYMBOLS
Drying
Symbols
Suitable for
dryer
No Iron
Do not dry-
clean
Sensitive /
Delicate dry
Do not dry
with dryer
Do not dry
Drying
Settings
Iron -
Iron at high
temperature
Iron at medium
temperature
Iron at low
temperature
Dry or Steam
IRON
200 0C
150 0C
110 0C
Maximum temperature
4.2 Laundry not suitable for drying in 4.4 Things to be done for energy
the dryer
saving
Following information will help you use the dryer in an
ecological and energy-efficient manner.
Delicate embroidered fabrics, woolen, silk
garments, delicate and valuable fabrics,
airtight items and tulle curtains are not
suitable for machine drying.
•
Spin your laundry at the highest speed possible
when washing them. Thus, the drying time is
shortened and energy consumption is reduced.
Sort out the laundry depending on their type and
thickness. Dry the same type of laundry together.
For example thin kitchen towels and table clothes
dries earlier than thick bathroom towels.
Follow the instructions in the user manual for
programme selection.
C
4.3 Preparing laundry for drying
•
•
Laundry may be tangled with each other after
washing. Separate the laundry items before
placing them into the dryer.
•
•
Dry garments having metal accessories such as
zippers, inside out.
Fasten the zippers, hooks and buckles and button
sheets.
•
•
Do not open the loading door of the machine
during drying unless necessary. If you must
certainly open the loading door, do not to keep it
open for a long time.
•
•
•
Do not add wet laundry while the dryer is in
operation
Clean the lint filter before or after each drying
cycle. (See 6 Maintenance and cleaning)
Clean the filter drawer regularly either when the
Dryer / User Manual
14 / 32 EN
Preparation
Filter Drawer Cleaning warning symbol appears or
Following weights are given as examples.
after every 3 drying cycles. (See 6 Maintenance
and cleaning)
Approximate weights
Laundry
(g)*
1500
1000
500
350
700
250
100
700
350
150
300
200
500
350
700
100
125
•
Ventilate the room, where the dryer is located, well
during drying.
Cotton quit covers (double)
Cotton quit covers (single)
Bed sheets (double)
Bed sheets (single)
Large tablecloths
Small tablecloths
Tea napkins
4.5 Correct load capacity
Follow the instructions in the “Programme selection and
consumption table”. Do not load more than the capacity
values stated in the table.
Bath towels
Hand towels
Blouses
Cotton shirts
Shirts
Cotton dresses
Dresses
Jeans
It is not recommended to load the dryer
with laundry exceeding the level indicated
Handkerchiefs (10 pieces)
T-Shirts
in the figure. Drying performance will
C
degrade when the machine is overloaded.
*Dry laundry weight before washing.
Furthermore, dryer and the laundry can get
damaged.
Dryer / User Manual
15 / 32 EN
5 Operating the product
5.1 Control panel
1
2
3
4
5
6
10
9
8
7
1. Programme Selection knob
2. Dryness Level Adjustment button
3. Audio Warning Level button
4. Display
5. On /Off/Cancel button
6. Start/Pause button
7. End Time button
8. Favourite button
9. Timer Programmes Selection button
10. Anti-creasing button
5.2 Display symbols
Dryness level
Audio warning smbol
Filter drawer cleaning warning symbol
Filter cleaning warning symbol
Water tank warning symbol
Start / Pause symbol
Child lock warning symbol
End time symbol
Remaining time indicator*
Programme progress bar
Smart grid symbol
*Time that appears on display indicates the
remaining time until the end of the programme
and changes according to the dampness level
of the laundry and model of the dryer.
Steam tank warning symbol
Dryer / User Manual
16 / 32 EN
Operating the product
5.3 Preparing the machine
5.6 Additional programmes
For special cases, following additional programmes are
available in the machine.
1. Plug in your machine.
2. Place the laundry in the machine.
3. Press the On/Off/Cancel button for 1 second
(long).
4. When your machine is operated for the first time,
it starts with the declaration programme (wardrobe
dryness for cottons.)
Additional programs may differ according
to the features of your machine.
C
To obtain better results from your
dryer, your laundry must be washed
C at suitable programmes and spun at
the recommended spin speeds in the
washing machine..
Pressing the On/Off/Cancel button
does not mean that the programme has
C started. Press Start / Pause button to
start the program.
5.4 Programme selection
1. Decide the appropriate programme from the table
below which includes drying levels.
•
Jeans
Use this programme to dry your jeans that are spun at
high speeds in the washing machine.
2. Select the desired programme with the
Programme Selection knob.
•
Mix
Use this programme to dry non-pigmenting synthetic
and cotton laundry items together.
Only the cotton laundry is dried at
normal temperature. Thick and multi
•
WoolProtect
Use this programme to dry woolen garments such as
jumpers that are washed according to the instructions.
It is recomended that garments would be removed at the end
of the programme.
layered laundry (towels, linens, jeans
and etc.) are dried in a way that they
Extra Dry
do not require ironing before being
placed in the wardrobe.
Normal laundry (tablecloths,
underwear and etc.) are dried in a
way that they do not require ironing
before being placed in the wardrobe.
The wool drying cycle of this machine
has been approved by The Woolmark
Company for the drying
of machine washable wool products
provided that the products are washed
and dried according to the
instructions on the garment label and
those issued by the manufacturer of this
machine.(M1447). In UK, Eire, Hong Kong
and India the Woolmark trade mark is a
Certification trade mark.
Cupboard Dry
Normal laundry (shirts, dresses and
Iron Dry
etc.) are dried ready to be ironed.
For further programme details, see
"Programme selection and consumption
C table"..
5.5 Main programmes
Depending on the fabric type, the following main
programmes are available.
•
Night
In this programme the level of noise emitted to the
environment will be the lowest. Volume level will be
fifty percent lower with respect to the ‘wardrobe dry for
cottons’ programme.
•
Cottons
Dry durable laundry with this programme. Dries at
normal temperature. It is recommended to use for
your cotton items (bed sheets, quilt covers, towels,
bathrobes, etc.).
Synthetics
Dry less durable laundry with this programme.
Recommended for synthetics.
•
Xpress
You can use this programme to dry your cotton laundry
that you have spun at high speeds in your washing
machine. This programme dries 1 kg cotton laundry (3
Shirts / 3 T-shirts) in 49 minutes.
•
•
BabyProtect
This programme is used for baby clothes that bear
machine dryable approval on its label.
Dryer / User Manual
17 / 32 EN
Operating the product
•
Daily
This programme is used to dry cottons and synthetics
daily, and lasts for 100 minutes.
•
Shirts 30’
Use this programme to make 2 shirts ready for ironing
in 30 minutes.
There may be a little moisture on the
shirts at the end of the programme. We
C recommend you not to leave the shirts in
the dryer.
•
Delicates
You can dry your highly delicate laundry (silk blouses,
fine underwear, etc.) that are suitable for drying or
laundry which is advised to be hand-washed at a lower
temperature.
It is recommended to use a cloth bag
to avoid certain delicate garments
C and laundry from getting creased or
damaged. Take your laundry immediately
out of the dryer and hang them after the
programme ends in order to prevent them
being creased.
•
Freshen Up
Only ventilation is performed for 10 minutes without
blowing hot air. You can air the clothes that have
been kept at closed environments for a long time and
deodorize unpleasant odors thanks to this programme.
•
Timer programmes
You can select one of the 10 min., 20 min., 30 min., 40
min., 50 min., 60 min., 80 min., 100 min.,
120 min., 140 min. and 160 min. timer programmes
to achieve the desired final drying level at low
temperatures.
With this programme, the machine dries
for the time selected regardless of the
C dryness level.
Dryer / User Manual
18 / 32 EN
Operating the product
5.7 Programme selection and consumption table
EN
2
Spin speed in washing Approximate amount
Programs
Capacity (kg)
Drying time (minutes)
machine (rpm)
of remaining humidity
Cottons / Coloreds
8
8
8
1000
1000
1000
% 60
% 60
% 60
184
174
139
Extra dry
A
Cupboard dry
A
Iron dry
A
Night
8
3
1000
1000
1200
1200
1200
1000
1200
600
% 60
% 60
% 60
% 50
% 50
% 60
% 50
% 40
% 50
240
95
Babyprotect
Shirts 30’
Jeans
0.5
4
30
117
100
110
49
Daily
4
Mix
4
Xpress
1
Delicates
Wool protect
Synthetics
2
50
1.5
600
146
4
4
800
800
% 40
% 40
75
59
Cupboard dry
B
Iron dry
B
Energy consumption values
Spin speed in washing Approximate amount Energy consumption
Programs
Capacity (kg)
machine (rpm)
of remaining humidity
value kWh
Cottons linen Ready to wear*
Cottons Ready to iron
8
8
4
1000
% 60
% 60
% 40
1,42
1000
1,05
Synthetics Ready to wear
800
0,51
Power consumption of the off-mode for the standart cotton programme at full load, PO (W)
Power consumption of the left-on mode for the standart cotton programme at full load, PL (W)
Contains fluorinated greenhouse gases covered by the Kyoto Protocol. Hermetically sealed.R134a / 0,520 kg
0,5
1,0
„Cotton cupboard dry programme“ used at full and partial load is the standard drying programme
to which the information in the label and the fiche relates, that this programme is suitable for drying
normal wet cotton laundry and that it is the most efficient programme in terms of energy consumption
for cotton.
* : Energy Label standard program (EN 61121:2012)
All values given in the table have been fixed according to EN 61121:2012 Standard. These values may deviate
from the values in the table according to the laundry type, laundry spin speed, environmental conditions and voltage
fluctuations.
Dryer / User Manual
19 / 32 EN
Operating the product
Dryness level adjustment selection
Dryness level adjustment button is used to adjust
the required dryness level. Programme duration can
change depending on the selection.
5.8 Auxiliary functions
Audio Warning
The machine will give an audio warning when the
programme comes to an end. Use the Audio Warning
Level button to adjust the sound level.
You can activate this function only before
the programme has started.
You can change the sound level either
before the programme starts or while the
C programme is in progress.
C
Drying level damp
Volume level low
Volume level high
Drying level normal
Drying level extra
Dryer / User Manual
20 / 32 EN
Operating the product
Anti-creasing
Anti-creasing symbol will illuminate at the
end of the programme if Anti-creasing
Anti-creasing programme duration may be
changed with the Anti-creasing selection button. You
can use Anti-creasing function to prevent laundry from
creasing if you will not take the laundry out after the
program has come to an end. This programme rotates
the laundry in every 240 second for selected time to
prevent creasing.Following images identify the level
changes.
C function is activated.
Favourite selection button
A programme with the set auxiliary function is saved
with Favourite selection button.When the product is
switched on and off, features of the saved programme is
displayed by means of Favourite selection button.
1. Select the programme with the programme button;
select the auxiliary functions such as Anti-creasing,
Dryness Level etc.
2. Press and hold the Favourite selection button for
about 3 seconds. Features of set programme will
be saved.
Anti-creasing 0 minute
Anti-creasing 30 minute
Anti-creasing 60 minute
End time
With the End Time function, the end time of the
programme may be delayed up to 24 hours. The time
on the display is the total of normal drying time and end
time.
•
•
Open the loading door and put the laundry in.
Select the drying program.
Press End Time button to set the desired time delay.
•
Press Start/Pause button. Time Delaying starts
countdown and the time delaying symbol lights
up on the display. The “:” in the middle of the
displayed delay time will flash.
Anti-creasing 120 minute
•
Additional laundry may be loaded / taken out
during the End Time period. At the end of the
End Time countdown process, End Time symbol
disappears, drying process starts and the
programme duration is displayed.
Press Anti-creasing button to activate
this function.
C
Dryer / User Manual
21 / 32 EN
Operating the product
Draining the water tank
If loading door is opened and closed
When the programme is completed, a warning symbol
will appear continously to remind that the water tank
needs to be drained.
during the End Time duration, the
C programme will switch to pause mode.
End Time function should be resumed
with pressing Start/Pause button.
For detailed information, see 6
Maintenance and cleaning.
C
If the water tank becomes full while the programme is
running, the warning symbol will start to flash and the
dryer will pause. Drain the water in the water tank and
press Start / Pause button to resume the programme.
The warning symbol turns off and the programme
resumes operating.
Changing the End time
If you want to change the time during countdown:
•
End Time is deactivated when the dryer is switched
off and on with On/Off/Cancel button. Restart the
dryer and repeat the End Time procedure for the
desired time.
Cleaning the filter drawer
Warning symbol flashes to remind that the filter drawer
needs to be cleaned.
•
When your dryer is operated for the first time, it
starts with the declaration programme (wardrobe
dryness for cottons).
For detailed information, see 6
Maintenance and cleaning.
Canceling End time function
If you want to cancel the End Time countdown and start
the programme immediately:
C
•
End Time is deactivated when the dryer is switched
off and on with On/Off/Cancel button.
•
Press Start/Pause button to start the programme
you have previously selected.
Loading door open
5.9 Warning symbols
This warning symbol Pause appears and programme
progress symbol flashes when the loading door of the
dryer is open.
Warning symbols may differ according to
the model of your machine.
C
Lint filter cleaning
When the programme is completed, a warning symbol
will appear continously indicating that the filter needs to
be cleaned.
For detailed information, see 6
Maintenance and cleaning.
C
C
If the filter cleaning symbol flashes
continuously, see 7 Troubleshooting.
Dryer / User Manual
22 / 32 EN
Operating the product
To deactivate the childproof lock:
5.10 Starting the programme
•
•
Press and hold Child Lock button for 3 seconds.
Child Lock is deactivated when the dryer is
switched off and on with On/Off/Cancel button.
Press the Start/Pause button to start the program.
Start symbol will light up to indicate that the
programme has started and “:” symbol in the middle
of the remaining time will keep flashing. Drying and
programme progress bar will be displayed alternately.
5.13 Changing the programme after it
has started
5.11.Progress of programme
•
After the dryer starts operation, you can change
the selected programme and dry your laundry in a
different programme.
•
•
•
Press and hold Start / Pause button for 1 seconds
to pause the programme.
Select desired programme by turning the
Programme Selection knob.
Press the Start/Pause button to start the program.
Adding / removing laundry while the dryer is
in operation
5.12 Child Lock
•
•
•
•
In order to add or take out laundry after the drying
programme has started:
Machine is equipped with a Child Lock which prevents
interfering with the current programme flow by pressing
any button.
Press the Start/Pause button to switch the dryer to
Pause mode. Drying process will pause.
While in Pause mode, open the loading door, add
or take out laundry and close the loading door.
Press the Start/Pause button to resume the
program.
To activate the Child Lock:
•
Press and hold Childproof Lock button for 3
seconds.
•
Child Lock symbol will appear on the display when
the Child Lock is activated.
Any laundry added after the drying
process has started may cause the
C clothes that are already dried in the
machine intermingle with wet clothes and
the result will be wet laundry after the
drying process is over.
You may repeat laundry adding or
removing process as many times as
C you desire during drying. However, this
process will increase the programme time
and energy consumption since the drying
process will be interrupted repeatedly.
Therefore, it is recommended to add
laundry before the drying programme has
started.
•
•
•
•
All buttons except the On/Off/Cancel and Child
Lock button on the control panel are deactivated
when the Child Lock is active.
Display symbols will not change even if the position
of Programme Selection knob is changed while the
child lock button is active.
When the programme selection knob is turned and
function buttons are pressed Child Lock warning
will be displayed.
To start a new programme after the current
programme is over or to interrupt the current
programme, the Child Lock should be deactivated.
Dryer / User Manual
23 / 32 EN
Operating the product
If you select a new programme by turning
the Programme Selection knob while your
C drier is in Pause mode, then the current
program is aborted and new programme
information is displayed.
Do not touch the inner surface of the
drum when adding or taking out laundry
while a programme is running. Drum
surface and dryer air within is hot.
5.14 Canceling the programme
To cancel the programme after the dryer is started:
•
Press and hold Start / Pause button for 1 seconds
to pause the programme and turn the programme
selection knob.
•
Press and hold On / Off / Cancel Button for 3
seconds and the programme will be cancelled.
As the dried laundry will be excessively
hot when you cancel the programme
A while the dryer is running, activate the
Refresh programme to cool them down.
5.15 End of programme
When the programme comes to an end Lint filter
cleaning and Water tank warning symbols light up in
the programme follow-up indicator. To turn off the dryer
press On / Off / Cancel button.
2-hour Anti-creasing program will be
activated if the laundry is not taken out
C after the program has come to an end.
Clean the lint filter after each drying. See
6.1 Cleaning lint filter and loading
C door inner surface.
Drain the water tank after each drying
cycle. See 6.3 Draining the water
C tank.
Dryer / User Manual
24 / 32 EN
6 Maintenance and cleaning
Service life of product extends and frequently
experienced problems will be reduced if it is cleaned at
regular intervals.
6.1 Cleaning Lint Filter / Loading Door
Inner Surface
Lint and fiber released from the laundry to the air during
the drying cycle are collected in the Lint Filter.
•
Clean the entire inner surface of the loading door
and loading door gasket with a soft damp cloth.
Such fiber and lint are generally formed
during wearing and washing.
C
A
Always clean the lint filter and the inner
surfaces of the loading door after each
drying process.
You can clean the lint filter housing with a
vacuum cleaner.
C
To clean the lint filter:
•
•
Open the loading door.
Remove the lint filter by pulling it up and open the
lint filter.
•
•
Clean lint, fiber, and cotton raveling by hand or with
a soft piece of cloth.
Close the lint filter and place it back into its
housing.
6.2 Cleaning the sensor
There are dampness sensors in the dryer that detect
whether the laundry is dry or not.
To clean the sensors:
•
•
Open the loading doorof the dryer.
Allow the machine to cool down if it is still hot due
to the drying process.
•
Wipe the metal surfaces of the sensor with a soft
cloth, dampened with vinegar and dry them.
•
A layer can build up on the filter pores that can
cause clogging of the filter after using the dryer
for a while. Wash the lint filter with warm water
to remove the layer that builds up on the lint
filter surface. Dry the lint filter completely before
reinstalling it.
Clean metal surfaces of the sensors 4
times a year.
C
C
Do not use metal tools when cleaning
metal surfaces of the sensors.
Dryer / User Manual
25 / 32 EN
Maintenance and cleaning
•
Drain the water in the tank.
Never use solvents, cleaning agents or
similar substances for cleaning due to the
risk of fire and explosion!
A
•
•
If there is lint accumulation in the funnel of the
water tank, clean it under running water.
Place the water tank into its seat.
If the direct water draining is used as
an option, there is no need to empty the
C
water tank.
6.4 Cleaning the filter drawer
Lint and fiber that could not be captured by the lint
filter are blocked in the filter drawer behind the kick
plate. Filter Drawer Cleaning warning light will light up
maximum at every 3 drying cycles as a reminder.
There is a two-level filter in the filter drawer. Te first level
is the filter drawer sponge and the second level is the
filter cloth.
6.3 Draining the water tank
Dampness of the laundry is removed and condensed
during drying process and the water that arise
accumulates in the water tank. Drain the water tank
after each drying cycle.
Condensed water is not drinkable!
A
To clean the filter drawer:
•
Press the kick plate button to open the kick plate.
Never remove the water tank when the
program is running!
A
If you forget to drain the water tank, the machine will
stop during the subsequent drying cycles when the
water tank is full and the Water Tank warning symbol
will flash. If this is the case, drain the water tank and
press Start / Pause button to resume the drying cycle.
To drain the water tank:
Pull the drawer and remove the water tank carefully.
•
Remove the filter drawer cover by turning it in the
direction of arrow.
Dryer / User Manual
26 / 32 EN
Maintenance and cleaning
•
Pull out the filter drawer.
•
Wash the filter drawer sponge by hand to remove
the fiber and lint on the surface. After washing the
sponge, squeeze it by hand and remove the excess
water. Well-dry the sponge before storing it.
It is not necessary to clean the sponge
if lint and fiber accumulation on it is not
significant.
C
•
Place the sponge back into its place.
•
Open the filter drawer by pressing the red button.
•
Close the filter drawer as to lock the red button.
•
Take out the filter drawer sponge.
•
Place the filter drawer back into its place, turn the
filter drawer cover in the arrow direction and close
it securely.
•
•
Clean lint, fiber, and cotton raveling on the filter
cloth by hand or with a soft piece of cloth.
When you notice a layer that may lead clogging on
the filter cloth, please clean the layer by washing
in warm water. Let the filter cloth dry thoroughly
before installing back the filter drawer.
Dryer / User Manual
27 / 32 EN
Maintenance and cleaning
•
Close the kick plate cover.
Drying without the filter drawer sponge in
place will damage the machine!
A
C
A dirty lint filter and filter drawer will cause
longer drying periods and higher energy
consumption.
6.5 Cleaning the evaporator
Clean the lint accumulated on the fins of the evaporator
located behind the filter drawer with a vacuum cleaner.
You can also clean by hand provided that
you wear protective gloves. Do not attempt
to clean with bare hands. Evaporator fins
can harm your hand.
A
Dryer / User Manual
28 / 32 EN
7 Troubleshooting
Drying process takes too much time.
•
•
•
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.
Ventilation grids on the front side of the machine are blocked. >>> Remove the objects (if any)
that block ventilation in front of the ventilation grids.
•
Ventilation is not sufficient since the room where the machine is installed is very small. >>> Open the
door and window of the room to avoid the room temperature increase too much.
Lime deposit has built up on the dampness sensor. >>> Clean the dampness sensor.
Excessive laundry is loaded. >>> Do not load the dryer in excess.
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing
machine.
•
•
•
Laundry comes out wet at the end of drying.
After drying, the hot clothes feel damper than their actual dampness level.
C
•
It is likely that the selected programme did not suit the laundry type.>>>Checking the care labels on
clothes, select appropriate programme for the laundry type or use timer programmes in
addition.
•
•
•
•
Pores of the lint filter are clogged. >>> Wash the lint filter with warm water.
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.
Excessive laundry is loaded. >>> Do not load the dryer in excess.
Laundry is not spun sufficiently. >>> Spin your laundry at a higher speed in your washing
machine.
Dryer does not switch on or the programme does not start. Dryer does not start when it is set.
•
•
•
It is not plugged in. >>> Make sure that the machine is plugged in.
The loading door is ajar. >>> Make sure that the loading door is closed securely.
Programme is not selected or the Start / Pause / Cancel button is not pressed. >>> Make sure that the
programme is selected and the machine is not in Pause mode.
•
Childproof Lock is activated. >>> Deactivate the Childproof Lock.
Programme is interrupted without any cause.
•
•
•
Loading door is ajar. >>> Make sure that the loading door is closed securely.
There was a power failure. >>> Press Start / Pause / Cancel button to start the programme.
Water tank is full. >>> Drain the water tank.
Laundry has shrunk, become felted or deteriorated.
•
A programme suitable for the laundry type is not used. >>> Check the garment tag and select a
programme suitable for the fabric type.
Drum lighting does not turn on. (On models with lamp)
•
•
Dryer is not switched on with the On / Off button. >>> Make sure that the dryer is switched on.
Lamp is defective. >>> Call Authorized Service Agent to have the lamp replaced.
End/Anti-creasing symbol is on.
•
Anti-creasing programme is activated in order to prevent laundry that has remained in the machine from
creasing. >>> Turn off the dryer and take out the laundry.
Dryer / User Manual
29 / 32 EN
Troubleshooting
End symbol is on.
•
Programme is over. Turn off the dryer and take out the laundry.
Lint Filter Cleaning symbol is on.
•
Lint filter is not cleaned. >>> Clean the lint filter.
Lint Filter Cleaning symbol is flashing.
•
•
Filter housing is clogged with lints. >>> Clean the lint filter housing.
A deposit has built up on the lint filter pores that may cause clogging. >>> Wash the lint filter with
warm water.
•
Filter drawer is clogged. >>> Clean the sponge and the filter cloth in the filter drawer.
Water leaks from the loading door
•
Lint has accumulated on the inner surfaces of the loading door and on the surfaces of the loading door
gasket. >>> Clean the inner surfaces of the loading door and the surfaces of the loading
door gasket.
Loading door opens spontaneously.
Loading door is ajar. >>> Push the loading door to close until you hear a locking sound.
Water Tank warning symbol is on/flashing.
•
•
•
Water tank is full. >>> Drain the water tank.
Water draining hose is bent. >>> If the product is connected directly to a wastewater drain, check the water
drain hose.
Filter Drawer Cleaning warning symbol is flashing.
•
Filter drawer is not cleaned. >>> Clean the sponge and the filter cloth in the filter drawer.
If you cannot eliminate the problem although you follow the instructions in this section, consult your
dealer or the Authorized Service Agent. Never try to repair a nonfunctional product yourself.
A
Dryer / User Manual
30 / 32 EN
8 Electrical Connection
Make sure that you have an earthed power outlet
socket rated at 13 amps (minimum).
Important
Fitting a different plug
A
As the colours of the wires in the mains lead
of this appliance may not correspond with the
coloured markings identifying the terminals on
your plug, proceed as follows:
1 Connect the green - yellow or green (earth) wire
to the terminal in the plug marked ‘E’ or with the
symbol or coloured green and yellow or green.
2 Connect the blue (neutral) wire to the terminal in
the plug marked ‘N’ or coloured black.
Attention!
If you use your dryer as built-in, the socket must
be reachable after installation, or a separate
switch (which can disconnect the two poles) must
be used in the installation. Check for suitability.
For a permanent connection, a master switch with
at least 3mm contact clearance and minumum 13
A rating must be used.
Electrical requirements
3 Connect the brown (live) wire to the terminal in
the plug marked ‘L’ or coloured red.
Before you insert the plug into the wall socket
make sure that the voltage and the frequency
shown in the rating label corresponds to your
electricity supply.
With the alternative plugs a 13A fuse must be
fitted either in the plug or adaptor or in the main
fuse box. If in doubt contact a qualified electrician.
We recommend that this appliance be connected
to the mains supply via a suitable switched and
fused socket in a readily accessible position.
Should the mains lead of the appliance become
damaged or need replacing at any time, it must
be replaced by a special purpose made mains
lead which can only be obtained from a Authorised
Service Agent.
Green and yellow
or green
A Warning
This appliance must be earthed
N
L
Blue or black
Brown or red
If the fitted moulded plug is not suitable for your
socket, then the plug should be cut off and an
appropriate plug fitted.
The moulded plug on this appliance incorporates a
13A fuse. Should the fuse need to be replaced an
ASTA approved BS1362 fuse of the same rating
must be used. Do not forget to refit the fuse cover.
In the event of losing the fuse cover, the plug must
not be used until a replacement fuse cover has
been fitted. Colour of the replacement fuse cover
must be the same colour as that visible on the pin
face of the plug. Fuse covers are available from
any good electrical store.
In order to avoid hazards, damaged supply cord
should be replaced by the manufacturer, its service
agent or similarly qualified people.
Dryer / User Manual
31 / 32 EN
|