Table of Contents
Important Safety Instructions....................................................................................................... 1
Federal Communications Commission........................................................................................ 4
Connecting the Monitor and Swivel Base.................................................................................... 2
Removing the Monitor and Swivel Base ...................................................................................... 2
Introduction.................................................................................................................................... 3
Installation...................................................................................................................................... 3
User Controls.................................................................................................................................. 4
OSD Function Description............................................................................................................ 4
OSD Icon Summary....................................................................................................................... 5
Specification.................................................................................................................................... 5
Troubleshooting............................................................................................................................. 7
Important Safety Instructions
1. Please read these instructions thoroughly.
2. Please keep this guide for future use.
3. Please disconnect the device from the main power supply before cleaning. Do not use any liquids or aerosol
sprays to clean this device. Use a clean dampened cloth in stead.
4. To avoid damaging the device, only use factory-approved accessories.
5. Protect the device against moisture.
6. In order to set up the device, first place it on a stable surface. Tipping it over or dropping can harm the
monitor and cause injuries. Please follow the setup instructions of the manufacturer while setting up your
monitor.
7. The ventilation openings are used for air circulation to protect the device against overheating.
8. When connecting the device, obey the maximum connected load values of the main power supply.
9. The wall socket must be equipped with a non-fused grounded conductor contact for electrical safety.
10. The power cable must be laid in such a way nobody can trip over it. Please do not place any objects on the
cable.
11. Follow all instructions and warning remarks that are printed on the device.
12. If the device will not be used for a long period of time, please disconnect it from the main power supply to
avoid power surge damage such as lightning.
13. Make sure no sharp objects or liquids enter the device via its air circulation openings. This could result in a
fire or an electric shock.
14. Never open the device casing yourself, there are no user serviceable parts inside. Only authorized technical
service personnel should open the casing of this device.
15. If any of the following conditions occur, the device must be disconnected from the main supply, and be
checked by a qualified service center:
a- Power cable or power plug are damaged;
b- Liquid has entered the device;
c- The device was exposed to moisture;
d- The device does not operate according to the user’s guide, or you do not achieve any improvement with
the aid of this guide;
e- The device has been dropped and/or the casing is damaged;
f- The device shows obvious signs of a defect.
16. Use only approved original spare parts, or parts in accordance with the original parts, for repairs. The use of
incorrect/unauthorized spare parts may cause further damage.
17. Please contact your service center for any questions regarding service and repairs to guarantee the device’s
performance and reliability.
18. The power socket must be installed near the equipment to be easily accessible.
1
Introduction
Congratulations on your purchase of this new high performance 17” Monitor. Using state-of-the-art
electronics, this monitor supports a 1280 x 1024 resolution. The on-screen display allows you to
customize the display settings to suit your individual taste.
Features
Ø17-inch monitor with a large, viewable screen
for comfortable viewing.
ØOSD user controls for easy and accurate
adjustment of the screen image.
ØEnergy Star compliant for reduced power
consumption.
Package Overview
Please make sure the following items are in the packing it was shipped in, and found in good
working condition:
n 17” Monitor
n Power Cord
n Tilt and Swivel Base
n This User’s manual
Please contact your dealer or nearest service centers if any of the above items is missing or damaged.
Installation
1. Connect the monitor signal cable
1
to the
15-pin mini D-sub (VGA) on the back of
the computer.
2. Connect the power cord
to the power
connector on the back panel of the monitor,
then plug the other end into an electrical
outlet that is easily accessible, and close to
the monitor.
3. First turn on the power of the computer,
then that of the monitor.
4. Adjust the tilt of the swivel base for
maximum viewing comfort.
The installation of your monitor is now
complete.
3
User Controls
1.
3.
Power Switch
Turns the monitor on
2.
4.
Power LED Indicator
LED color
Green
Status
On
Amber
Sleep
Select Button
Backward and Forward Buttons
·
·
Launches On -Screen Display
Make sure the select functions
or adjustments
·
Backward button (left arrow) moves
backward through menu options or
decreases adjustment levels.
·
Forward button (right arrow)
moves forward through menu
options or increases adjustment
levels.
·
Exit menus and On-Screen
Display
OSD Function Description
1. Press the
key to display the OSD menu.
2. To select a function, press the
the desired function is highlighted.
and
keys until
3. Press the
key to choose the function.
4. Use the
and keys to increase or decrease the
parameter level of the setting.
5. Press the
6. Select the
key to save the new setting.
icon if you want to exit the OSD
key once.
function, and then press the select the
4
OSD Icon Summary
Icon
Function
Brightness
Contrast
Function Description
Adjusts display brightness
Adjusts display contrast
H. Size
H. Position
V. Size
Increases and decreases screen width
Shifts display image right or left
Increase and decrease screen height
V. Position
Pin. Balance
Pincushion
Parallelogram
Trapezoid
Rotation
Shifts display image up or down
Adjusts each side of Pincushion
Adjusts concave and convex portion of pincushion effect
Adjusts the tilt of the display sides to the left or right
Adjusts the top and bottom display widths
Adjusts the rotation of the display clock or anti-clockwise
Adjusts the warmth of the displayed colors
Resets to default values
Color Temp.
Reset
Degauss
Demagnetizes the screen to reduce color impurities
Exit
Exits the OSD menu
Specification
Screen
Size
17” CRT
Dot Pitch (mm)
0.27
Surface
Viewable Image Area
Non –glare
16.14” (41.0 cm)
Input Signal
Video Sy nc.
RGB Analog 0.7Vp -p/75 Ohm
a. Separate H/V,TTL(+/-)
b. Composite H+V,TTL(+/-)
Scanning Frequency
Horizontal (KHz)
Vertical (Hz)
30-70
50-160
Max. Resolution
1280 x 1024
Signal Cable
Power
15-pin mini D-sub
Consumption
Power Supply
Power Management
Max. 75 W
100 - 240VAC (W/I CE Mark) 50/60Hz
Complies with EPA Energy Star ,VESA,
Nutek
Display Modes
Operating
Relative Humidity
Dimensions (L x W x H) 419 x 405 x 427 (mm)
Weight Unpacked
Preset
By User
6
14
Operating Temperature 0-40°C
10-90 %
14.9 Kgs (32.85 lbs)
5
Packed in box
16.8 Kgs (37.04 lbs)
6
Troubleshooting
Please refer to the following solutions for the failure symptoms that occur the most frequent. If the
symptom remains after trying these suggested solutions, please contact your local authorized service
center.
Problem: Power LED is not lit when monitor is powered on.
@Check to make sure that the power cord is connected properly.
@Make sure that the extension cord or the surge protector is turned on if the monitor is plugged
into a power extension cord or a surge protector.
Problem: No display appears on screen.
@Make sure that the computer switch is in the “On” position.
@Make sure that the video cable’s D-shaped connector is properly connected to the video
adapter port on the back of the PC.
@Check to make sure that the brightness and contrast controls are not turned to their dimmest
position.
Problem: Display image is either flickering or unstable.
@Make sure that the video cable’s D-shaped connector is connected properly to the video
adapter port on the back of the PC.
Problem: Image is bouncing or in a wave pattern.
@Move any electrical devices that can cause interference away from the monitor.
(Note: Please refers to the FCC statement at the beginning of the manual for more details on
display interference.)
7
|