Installation Guide
Solecis AVB-DA-RGBHV-0106
Safety Instructions
Overview
Please read these instructions before using your AMX Solecis device. Failure to
comply with these instructions could result in fire, electrical shock, personal injury,
death, or damage to the equipment.
The Solecis AVB-DA-RGBHV-0106 1:6 RGBHV Distribution Amplifier
(FG1340-4516-01) is a 1 in 6 out RGB HV distribution amplifier on BNC
connectors. All outputs are 75 ohm driven for connection to long cable runs.
Power Source
The high performance wide bandwidth circuitry ensures compatibility across all
resolutions and the AVB-DA-RGBHV-0106 can be used for RGBHV, RGBS,
RGsB, YUV, and composite video.
Use only a 3-wire grounding type source. The power source should not exceed
264VAC. Do not remove under any circumstances the ground wire.
Power Cord
The AVB-DA-RGBHV-0106 is housed in a 1U metal enclosure and features an
internal 100-240V power supply.
Use only the cord shipped with the unit. Do not use the cord if it has become damaged
or frayed. Contact your AMX Solecis dealer if you need to replace the power cord.
Grounding
(front)
The interface is grounded through the grounding conductor on the power cord. To
avoid electric shock plug the power cord into a properly wired receptacle. Do not
defeat the purpose of the grounding-type plug.
Fuse
For protection against the risk of fire, use only a fuse of the same rating and type.
Liquid Spills
Do not set drinks on top of the unit or immerse the unit in liquid.
Do Not Disassemble
This device contains no user serviceable parts. All servicing must be performed by a
qualified service technician.
(rear)
FIG. 1 Solecis AVB-DA-RGBHV-0106
For Safety Reasons
Product Specifications
•
•
•
•
Do not place the unit on an unstable surface.
Do not use near water or sources of heat.
Use only recommended attachments.
Use the type of power supply as specified.
AVB-DA-RGBHV-0106 Specifications
RGB Input
Unplug the power to the unit and refer servicing to qualified personnel under the
following conditions:
Number:
1
•
•
If liquid has been spilled or the unit has been exposed to rain or water.
If it does not operate normally when the operating instructions are followed or if it
exhibits a distinct change in performance indicating a need for service.
If the unit has been dropped or the cabinet damaged.
Connector:
Level:
BNC
Analog
1V p-p
75 ohm
•
Max Level:
Connections
Connect the PC input and outputs on the rear panel of the unit.
Impedance:
Sync Input
Type:
Note: It is imperative that the input source is fully compatible with the display
devices.
Analog or TTL
Impedance:
RGB Video Bandwidth:
RGB Return Loss:
75 ohm
The RGB input is 75 ohm terminated and the outputs fully 75 ohm driven for
connection to long cable runs.
350MHz -3dB
The unit can now be connected to the mains and the power switched on.
-40dB@10MHz, -27dB@100MHz
Adjacent Channel X-talk: -70dB@10MHz, -48dB@100MHz
RGB Output
Number:
Connectors:
Level:
6
BNC
Analog
Unity
75 ohm
Gain:
Impedance:
Sync Output
Level:
TTL
Impedance:
Power
75 ohm
Input Voltage:
Power Consumption:
Dimensions (HWD):
Weight:
100-240V 50/60Hz
8W
1.73” x 17.36” x 6.69” (4.4cm x 44.1cm x 17.0cm)
5.73 lbs. (2.6kg)
Certifications:
• CE
• UL60950
• FCC class B, part 15
• RoHS/WEEE compliant
|