|
#
Convenience Store Intercom
System
Model C5000
Operating Instructions
Model C5000
Important Information
Intended Use
The 3M™ Convenience Store Intercom System, Model C5000, is designed to
provide 2-way audio communication in quick service drive-through restaurants
and convenience stores.
FCC Information
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
3M 1998 July
Model C5000
System Description
The 3M™ Convenience Store Intercom System, Model C5000, enables store
personnel to communicate with customers calling in from Call Stations at up to
16 pumps or other remote locations.
Introduction
The system arranges incoming calls in a first-come first-served order. The
operator can also choose to talk to any customer at any Call Station at any time.
Operators using wireless headsets or belt packs can also talk to each other using
the paging feature.
During peak hours, pushing the FUEL button on the Call Station sends a call to
a fuel operator. Pushing the FOOD button sends a call to a food operator.
During non-peak hours, pushing either button sends a call to the operator on
duty (if this option is installed and selected).
Operators use Station Selectors, headsets, belt packs, or a combination of these
components to communicate with customers.
System Components
Figure 1. Station Selector, Headset, and Belt Pack
Customers use Call Stations at the pumps to communicate with operators.
Figure 2. One-Button and Two-Button 3M™ Call Stations
The system can be operated from the Station Selector(s), the headset(s), or the
belt pack(s).
Operating Modes
STANDBY Mode
In the STANDBY mode, the Station Selector, headset, or belt pack is on and
waiting to receive a call from a customer or other operators.
TALK/LISTEN Mode
ALL CALL Mode
PAGE Mode
Use the TALK/LISTEN mode to talk or listen to the customer.
Use this mode to talk to all Call Stations at the same time.
Use this mode from the headset or belt pack to talk to other operators without
the customer hearing the conversation.
Call Merge
Use the Call Merge switch to control who receives incoming calls. The Call
Merge Switch (not shown) is a single-pole, single-throw switch. NORMAL
position is open; MERGE position is closed. Slide the button to MERGE to
send all calls to the on-duty operator during off-peak hours. Slide the button to
NORMAL to direct FOOD calls to FOOD operators and FUEL calls to FUEL
operators during peak hours.
3M 1998 July
1
Station Selector Controls and Indicators
Model C5000
The Station Selector controls are shown below.
Station Selector
Figure 3. Station Selector, Controls, and Indicators
ON turns on the Station Selector; OFF turns it off.
1 POWER Switch
! Note
The remotely located communications controller and the Station Selector are
designed to be left on. Notify your system administrator or manager if the
Station Selector power switch is off and turning it on does not illuminate the
power indicator light.
Turn to increase; or decrease the volume in the Station Selector speaker.
Lights to indicate the Station Selector power is on.
2 VOLUME Control
3 POWER Indicator
4 Station Selector
Keys
Press to initiate or answer a call to a specific Call Station.
(Station Selectors come in either 16-station or 8-station units.)
5 Call Indicators
1 through 16
(amber)
Lights in amber to indicate call status:
Flashing Light = A call is waiting to be answered.
Light Steady On = Call has been answered and connection is established to
the customer
Press to connect to the calling location. Hold to talk to the customer. Release
to listen.
6 TALK Key
Lights (red) when TALK key is pressed and held to indicate the system is in
talk mode. Extinguishes when the TALK key is released.
7 TALK Indicator
8 LISTEN Indicator
9 STANDBY Key
Lights (green) when TALK key is released to indicate the system is in listen
mode.
Press to end a call and return the system to the standby mode.
Lights to indicate the system is in standby mode.
10 STANDBY
Indicator
11 ALL CALL Key
Press to broadcast a call to all Call Stations at the same time.
2
3M 1998 July
Model C5000
Station Selector Operating Procedures
When a customer presses a Call Station button, the amber call indicator key for
that Call Station (1 through 16) flashes on the Station Selector and an
intermittent tone sounds.
Operating the
Station Selector
The system arranges calls from customers in a first-come first-served order.
To answer a call from a Call Station, do the following:
Responding to a Call
1. Press and hold the TALK key to talk to the first customer in order.
•
•
•
The call indicator light stops flashing, but remains lit.
The red talk indicator lights.
The system automatically connects to the first customer.
2. Release the TALK key to listen to the customer.
•
•
The green listen indicator lights.
The call indicator remains lit.
3. When finished talking and listening to the customer, press the STANDBY
key.
•
•
The call is disconnected and the call indicator turns off.
The standby indicator lights.
4. If other call indicators are lit, repeat Steps 1 through 3 to answer each call
in order.
To override the call order, press the Station Selector number key for the desired
Call Station. The Station Selector enters LISTEN mode for the selected Call
Station. Perform TALK, LISTEN and disconnect functions as described in
Steps 2 through 4 above.
Initiating a Call
To call a specific Call Station from the Station Selector, do the following:
1. Press the selection key for the desired call station.
•
•
•
The amber call indicator for the selected Call Station lights.
The standby indicator light goes off.
The green LISTEN indicator lights.
2. Press and hold the TALK key to talk to the customer.
•
•
The call indicator remains lit.
The red talk indicator lights.
3. Release the TALK key to listen to the customer.
•
•
The green listen indicator lights.
The call indicator remains lit.
4. When finished talking and listening to the customer, press the STANDBY
key.
•
•
The call is disconnected and the call indicator turns off.
The standby indicator lights.
Repeat Steps 1 through 4 to initiate another call.
! Note
If VOX (Voice Activated Transmission) is enabled on your system, you can
speak to the customer without pressing TALK once a connection to a Call
Station has been established.
VOX
Speak within two inches of the microphone to be heard clearly. Remember that
conversations in the store can be heard through the open microphone and that
the connection remains open until you press STANDBY to disconnect.
To talk to all Call Stations at the same time, press and hold the ALL CALL key.
Release the ALL CALL key when the message is completed.
ALL CALL
3M 1998 July
3
Headset and Belt Pack Operating Procedures
Model C5000
The Model C960AA Headset and Model C860AA Belt Pack Intercom controls
are shown below.
Headset and
Belt Pack
See the 3M™ Headset Intercom System, Model C960, Operating Instructions
and the 3M™ Belt Pack Intercom System, Model C860, Operating Instructions
for detailed information about headset and belt pack operations.
Figure 4. Headset and Belt Pack Controls
Press the ON switch to turn on the headset or belt pack.
Press the OFF switch to turn off the headset or belt pack.
Press to increase the volume. There are 15 available volume levels.
1 ON Switch
2 OFF Switch
3 Volume Up ▲
Control
Press to turn the volume down.
4 Volume Down ▲
Control
Press either switch to connect to the calling location. Hold the switch to talk to
the customer. Release the switch to listen.
5 Talk Switches
(T1 or T2)
! Note
If your location has more than one wireless system, contact your local dealer for
information about Talk switch (T1 and T2) operations.
Momentarily press and release to activate the Call Station scan feature.
(Also used to disconnect a Call Station and return the system to standby mode.)
6 Page/Call Station
Scan Switch
Press and hold to talk to internal personnel without being heard by the
customer. Release the switch to listen. (With the switch released, you can hear
both customers and internal paging.)
7 TALK/Lock Switch Not used for this application.
Push the battery release up and hold it while sliding the battery out of the
8 Battery Release
housing.
! Note
The C860 Belt Pack operates with either 1 or 2 batteries. If 2 batteries are used,
replace both at the same time.
4
3M 1998 July
Model C5000
Station Selector Operating Procedures
To answer an incoming call, do the following:
Operating Headsets
and Belt Packs
1. Press and hold either TALK key (T1 or T2) to connect to the first customer
in order.
•
•
The tone stops.
The amber call indicator on the Station Selector paired with the headset
(if used) stops flashing, but remains lit.
2. Release the key to listen to the customer.
•
•
The enunciator announces the Call Station number.
You can then listen to the customer.
To answer an incoming call, do the following:
Responding to a Call
1. Press and hold either TALK key (T1 or T2) to talk to the first customer in
order.
•
•
The tone stops.
The amber call indicator on the Station Selector paired with the headset
stops flashing, but remains lit.
2. Release the key to listen to the customer. The call indicator remains lit.
3. When you are finished talking and listening to the customer, press the
PAGE key (P). The call is disconnected and the call indicator turns off.
4. To respond to the next caller, repeat steps 1 through 3 to answer each call in
order.
To ignore the next call in order and talk to a customer at a specific Call
Station, quickly press and release P once. The enunciator announces the
numbers of each Call Station awaiting a response. When you hear the
number of the desired Call Station announced:
•
•
Press T1 or T2 to talk to the customer.
Release to listen.
To initiate a call to any Call Station:
Initiating a Call
1. The system must be in STANDBY mode.
2. Momentarily press and release the PAGE (P) switch.
•
•
The system enters the Call Station scan mode.
The enunciator announces ”Select...All Call... One..Two...Three...”.
3. When the enunciator announces the number of the Call Station you want to
call, press and release T1 or T2.
•
The enunciator announces “Connect One” (or the number of the Call
Station you selected).
4. Press and hold T1 or T2 to talk to the customer.
5. When you are finished talking and listening to the customer, press P.
•
The Call Station is disconnected and the call indicator on the Station
Selector turns off.
Repeat Steps 2 through 5 to initiate another call.
Press and hold P to talk to other operators wearing headsets or belt packs.
Release when the message is completed.
Paging
! Note
Disable the TALK/LOCK feature on all headsets used with the Model C5000.
See the 3M™ Headset Intercom System, Model C960, Operating Instructions
and the 3M™ Belt Pack Intercom System, Model C860, Operating Instructions
for detailed information about disabling this feature.
Installation
Instruction Note
3M 1998 July
5
3
InTouch Products
Food Service Trades Business
Commercial Care Division
Printed on 50% recycled
waste paper, including 10%
post-consumer waste paper.
Printed in U.S.A.
3M 1998 July
78-6912-0700-1
3M Center, Building
St. Paul, MN 55144-1000
|